|
|
 |
|
-
Our entry level VoIP calculator allowing you to easily calculate your Voice over
IP bandwidth requirements.
Available for immediate download at only 99 US Dollars.
|
|
-
Design and use your own VoIP calculators using drag and drop techniques.
We used this software to design our own VoIP calling
service. Now, we offer it for everyone to use.
|
|
-
Simplifies the complicated design process involved in creating effective voice
networks.
Support both traditional circuit switching techniques and Voice over IP.
|
|
|
 |  | MikeM to Dirceu Ciupka - 12 Apr 2010 | | |
|
Posted on www.erlang.com
Dirceu,
There is a document on quintum's web site that may help on this. Just search for SIP on there web site. The basic is that you need to set the quintum to register to your sip server and then your sip server will control the routing.
MikeM
mike_voip@hotmail.com |
| | Dirceu Ciupka - 8 Apr 2010 | | |
|
Posted on www.erlang.com
Dear,
I am tryng to setup a Quintum DX 4060.
One side is a SIP TRUNK provided by a Asterisk PBX, and other side a PSTN 2 Mb MFC-R2.
I can do orig calls, but dont incoming calls.
Can you help me with any information?
Grasiously,
Dirceu Ciupka |
| | Abrar Aslam - 16 Oct 2009 | | |
|
Posted on www.voip-calculator.com
I want to change the configuration of Quintum Tenor 960 from H323 to SIP. Please explain me what setting do I need to change. |
| | MikeM to Sardar - 4 Jul 2009 | | |
|
Posted on www.erlang.com
Sardar,
that is pretty general question. There are many ways to configure quintum for use with SIP. If it is orig, you will need to configure the quintum to connect through a sip server (you must provide). If it is for term, then you do not need to do anything different than you would for H323.
If you need further assistance, please contact me directly at
mike_voip@hotmail.com |
|
Posted on www.voip-calculator.com
Hi all,
i want to configure a quintum dx for sip calls, i'm asking if you have any idea of how to configure dx for sip?
thank you for your help
sardar77@hotmail.com |
|
Posted on www.voip-calculator.com
Hi all,
i want to configure Tenor dx for h323 config, i want it to work with AVAYA S8720 with both equipment should be on the same setup.how do i do it.
thanks you all. |
| | MikeM to DDDD - 9 Apr 2008 | | |
|
"Please answer Now" a little impatient it seems.
In any case, if you would like me to provide you the full config, but again, there is no guarantee that this this will work, you may send me a message direct to my email of
mike_voip@hotmail.com
MikeM |
|
to mikeM
hallo, tahnks for your answer....
my the software on the quintum A800 is have updated with :
Product Name: Tenor Analog A800 Multipath Switch - 8 ports (Rev. B)
Gatekeeper Status: Mini
GK Calls Allowed: 8
Feature Bit Status: -PS/+RB/-ER
Languages allowed: 1
Serial Number: A002-0082A9
Ethernet Address: 00-30-E1-00-82-A9
IP Address: 192.168.68.3
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.68.1
System Software Version: P5-2-1(LEC) (1678285/0xFF74)
Boot Software Version: P4-1-3 (180592/0xE814)
Database Version: 2.08 09-13-2000 (278376)
that is dekripsion config of my quintum. so how to make this quintum work in the port SIP.
thanks for your answer...
please answer Now.
thanks you |
| | MikeM to dddd - 3 Apr 2008 | | |
|
If you are talking about the older generation 1 A800, you need to understand a couple of things;
1. Quintum no longer makes nor supports this model.
2. There is a "BETA" sip software on their web site for this model, but like the A800, it is not supported. Worse yet, because it is beta, it was never fully tested. It was actually created in 2004 so it is 4 years old with no updates since or after.
You can try to use this, but I have seen about 50% success rate with this software and the unit. If your requirement is SIP, I suggest you purchase the newer quintum, AX800 that fully supports SIP.
MikeM
mike_voip@hotmail.com |
|
how to use quintum a800 with sip configuration to make 2 port of pbx on quintum,,,,?
thanks you for your question.. |
|
|
|
 |
Post a reply to this article
|
|
|
|
|
|
