|
|
 |
|
-
Our entry level VoIP calculator allowing you to easily calculate your Voice over
IP bandwidth requirements.
Available for immediate download at only 99 US Dollars.
|
|
-
Design and use your own VoIP calculators using drag and drop techniques.
We used this software to design our own VoIP calling
service. Now, we offer it for everyone to use.
|
|
-
Simplifies the complicated design process involved in creating effective voice
networks.
Support both traditional circuit switching techniques and Voice over IP.
|
|
|
|
Posted on www.voip-calculator.com
i have AXT1600 and 2 prefix comming on my quintum, i want to allocate these ports on 2 prefixes like first 8 ports on 8892 and rest 8 ports on 1192
i have added Cassig line 2, HND 2, and TCRG line2 and also added in Analog Line interface
but i m getting error code 9. can u please tell me what is the problem ??? |
|
Posted on DualSoftswitch.com
How to control web baseas quintum |
|
Posted on www.voip-calculator.com
Thanks for the reply, Mike. I found some doc on this MS ISA 2006 fw that we are using and there may be some inherent problems with it supporting SIP. I have a new fw ordered. Likewise I'm hoping there isn't a double-natting problem which could cause sim probs I've heard- even with the new fw. We shall see. |
 |  | MikeVoip to Jesse - 4 Jul 2009 | | |
|
Posted on www.erlang.com
Jesse,
the problem is very obvious. Your firewall is blocking the voip ports from being passed through or you have not configured the external/public IP into the CMS.
First step is make sure your firewall is truely opening all ports to/from the CMS.
Next is to check the config of the CMS in the ethernet interface area.
Mike_voip@hotmail.com |
|
Posted on www.voip-calculator.com
Hi Folks,
I have a CMS that was recently put behind a software firewall. It's basically in a DMZ until we can get calls working. Problem is that on every call now we get one-way audio. Caller can hear called every time.
It worked fine until we added the firewall. Any suggestions?
Thank you,
Jesse |
| | MikeM to Deen - 11 Feb 2006 | | |
|
Deen,
There are many. Maybe if you contact your ISP they can switch the modem to one that has standard RJ45 connector. Otherwise, you can get a linksys. |
| | Deen to MikeM - 11 Feb 2006 | | |
|
Thank you Mike for your advice. I have an ADSL and my ISP has given me a static IP. They have also provided me a modem with only USB connector (male) which works with my pc well. But my tenor has no USB port. Is there any ADSL modem with RJ45 connector that can be used for connecting my tenor to internet directly? If so, Will it be possible to access my tenor from different networks?
Deen |
|
| With the generation 2 quintums, if you lose your password, you will need to contact quintum directly to have it reset. |
| | Tareq Mahmud - 10 Feb 2006 | | |
|
Hallo
I have lost my GW password
My GW is AXT800
Do you know this solve
plz help me
Tareq mahmuh |
| | MikeM to Zubi - 9 Feb 2006 | | |
|
Zubi,
You have many questions on A400 and SIP. Here are the answers;
1. No, you cannot have both H323 and SIP working at the same time in the A400. There is not enough memory in the older, like A400, units to support both. In the Generation 2 units, you can have both working at the same time, but only for recieving calls from IP. You would need to pick 1 for sending calls to IP.
2. As always, you should go to Quintum's web site under the support pages and you will find all the information you need to know how to upgrade your unit.
3. As long as the unit is not reset after the connection is lost, then it should be ok and you can resume your upgrade. If the unit resets after the lost connection, but before you finish the upgrade, the system will be locked up and you will need to perform a system recovery.
4. They are different parts of the software that the tenor uses to run. If you read the release notes for each version, it will tell you which software needs to be upgraded. Also, in the directions for upgrading your unit, it should describe the files somewhat.
5. There is a different system software. Again, review the release notes on Quintum's web site.
6. For the older units, like A400, the SIP software is only beta version. Not full version and I hear that there are problems. Even on the newer units, generation 2 units, SIP is not 100%. Personally, I believe that H323 is much more stable. |
|
|
|
 |
Post a reply to this article
|
|
|
|
|
|
