|
 | Erlangs calculation in a VoIP network | |  |
|
 |
|
-
Our entry level VoIP calculator allowing you to easily calculate your Voice over
IP bandwidth requirements.
Available for immediate download at only 99 US Dollars.
|
|
-
Design and use your own VoIP calculators using drag and drop techniques.
We used this software to design our own VoIP calling
service. Now, we offer it for everyone to use.
|
|
-
Simplifies the complicated design process involved in creating effective voice
networks.
Support both traditional circuit switching techniques and Voice over IP.
|
|
|
| | Sumit Sharma - 16 Apr 2010 | | |
|
Posted on www.voip-calculator.com
Could you please let me know what is the formuale to convert Minutes of Usage to erlang? |
|
| That's true for conventional telecommunication. However, VOIP is runned over packet switched network. What about multiplexing gain ? |
| | Erlang Model - 3 May 2004 | | |
|
Forget the fact that the transport media is IP, understand the behavior of the VOIP as..
TDM ---VOIP ---TDM connection, the same calculation applied to TDM circuits applied to IP circuits once the only thing that changes is the transport media and the compression provided by the codecs on the media gateways.
follow the result of the 0.35 milierlangs that you used to have on TDM, however this will work only for Prepaid calling cards, Corporative users or Home users, if you try to apply the calculation to wholesale carriers you will find that every carrier will use the available ports in a 1 to 1 relation begining PEAK-TIME.
Regards,
Saul Bejarano |
|
thanks for your reply. first of all.
I was not clear explaining my point originally.
I of course see a relation between the erlang traffic model and the VoIP transport across an IP network (bandwidth concerns)
For my particular case I'm starting from the point of a VoIP deployment in LAN conditions (100 Mb network, even Gb links), and for the amount of calls that I will ultimately intend to support, my bottleneck is the PSTN access (because I depend on the PRI's/ Analog trunks)
I guess I'm curious to know how the Erlang model applies to this case (when you have enough bandwidth to support even VoIP Linear codec calls.)
I am using the Erlang model to calculate the distribution of PRI trunk channels versus VoIP endpoints depending on our foreseen traffic needs an obtain the peak BHCA/BHCC/CCS/Erlang figures that this equipment must support
I am using the number of PRI channels, the amount of peak trafic (typical BHCA/BHCC rate) (% of acceptable calls lost due to circuit unavailables) to get the figures. But assuming that the IP network is not an issue for bandwidth concerns, I don't see how a VoIP approach is different than a traditional approach (this is what I am curious indeed)
Our WAN VoIP traffic is minimal and to some extent not prioritary these days (Inbound PSTN still produces 98% of our traffic).
thanks anyway for the information
VoIP benigger |
|
The Erlang model is just as applicable to VoIP systems too, to argue it doesnt is to show a complete lack of knowledge of telecommunications principles (note I say telecommunications, not voice!)
In a voip network there will be a requirement for a certain amount of voice traffic, expressed as erlangs. CCS, call minutes or whatever. Erlang tables convert this to a quantity of 'channels' to carry that traffic. Each 'channel' is the equivalent of the voice compression standard (G.711, G.729A/B etc) plus IP overheads.
For instance, 10 Erlangs of traffic requires 18 lines/channel to carry that traffic. At 64kb (G.711) compression plus Ip overhead each 'channel' occupies 80kb, therefore the MINIMUN bandwidth for your network needs to be 18 x 80kb= 1.44Mb just to carry voice. This is easily achievable across a local 100Mb LAN, but must be considered if you are considering VoIP via say a 256kb DSL style connection.
Increase the number of phones, ERLANGS increase, bandwidth requirement increases. Once you hit b/w near 10Mb you may need to investigate the capability of hubs, switches and routers!
Throw in some IP video-conference and your LAN may just begin to sssllloooowwwwww down. |
| | Heber Alfaro - 27 Apr 2004 | | |
|
I'm evaluating the voIP solution of an IP-PBX company and it seems they have a distributed architecture and add lines & trunks depending on my needs.
They say that the Erlang model does apply only to the trunk to pstn part of the picture and they warranty that their PRI's can support up to 23 simultaneous calls or their analog trunk switches can support also 23 simultaneous calls.
so my question is. How can I relate the Erlang traffic model to calls originated from the VoIP network?
(calls can be made from IPPhones, softphones or analog-to-voip converter's in an unlimited way)
In other words.. I do not see how the Erlang model applies to the IP-PBX except in the trunk-topstn interface.
am I correct in my appreciations or there is something else I should take into account
thanks
any help would be trully appreciated
;-) |
|
 |
Post a reply to this article
|
|
|
|
|
|
